| |
• Using SpeediBleed™
before each meet to perform a complete
brake fluid flush,will ensure a firmer pedal on race day,and the
extra confidence,knowing your cars brake fluid is maximized for
performance.
• Regular brake fluid flushing
on all vehicles is important,but the increased demands placed on
the braking system by the severe driving conditions that exist during
a race,makes this service even more critical for racers.
 |
•
SpeediBleed™ will
perform a complete brake fluid flush,faster,and with more
ease and effectiveness than any other tool or method.You will
perform this important pre-race task in aprox.
20 minutes, decreasing the
possibility of brake fade or other brake fluid related problems,occuring
on race day.
• The speed,ease of use,and
portability of SpeediBleed™
makes it a tool equally suitable
for work in the shop,home garage,or track side. |
The Ideal Shop Tool
:  Ounce
of prevention or pound of cure |
 |
• SpeediBleed™
is a small, light weight, totally re-designed
pressue bleeder. Many of SpeediBleed's
most committed customers were tempted
at 1st glance to compare it with tools they had previously used
and dis-liked. What caused the change of opinion ? THEY USED IT
! It is that simple.
" Excellent tool, we have
3 of them in our shop, they are always being used"
George Heer, MCL Motor Cars Inc.
• After using SpeediBleed™
on only a few vehicles, you will discover
the following:
1. Hookups
of only 2-3 minutes.
2. Simple,leak resistant
adapters
3. Complete brake fluid flush in aprox.
20 minutes.
4. Firmer
brake pedal and clean fluid.
5. Total control of the brake bleeding / flushing procedure. |
|
|
• SpeediBleed™
has a customer satisfaction rating higher
than any conventional pressure bleeder,and its simplicity and effectiveness
allow it to outshine all other methods.
SpeediBleed™ a day keeps the brake
fade away
• Brake fluid is hygroscopic meaning
it absorbs moisture.
• Regular brake fluid flushing will result in higher boiling
points.
• 3 % moisture
content drops the brake fluid boiling point by as much as
170° F.
• Brake fade is caused by vapour
lock, i.e. small compressible air bubbles that
occur when heat transfer from the caliper to the brake fluid causes
the fluid
to boil.
• The most common cause of vapour lock is moisture contaminated
brake fluid.
• The lower the brake fluid boiling point,the lower tempature
at which the fluid
starts to create air bubbles,leading to a softer,spongier brake
pedal.
• The worst,though seldom,case of brake fade can result in
total loss of pedal.
• SpeediBleed™
will perform a pre- meet brake fluid
flush in aprox. 20 minutes,
decreasing the possibility of brake fade
on race day.
| The Ideal Track Side
Tool : Fast
, Portable , Effective |
 |
• Due to SpeediBleed™'s
portability and speed of use, it will
make a terrific “just in case” adittion to your track
side equipment.
• If you do experience brake fade during
a race , performing a complete brake fluid flush before the
next race is required , over just allowing the fluid to cool down.
After brake fluid has overheated ,
boiled , and cooled off , it will have a lower boiling point , resulting
in higher possibility of future
brake fade.
| • Taking
SpeediBleed™
to the track will provide piece of mind , and extra confidence
, knowing that should your car require between race brake
fluid service , the procedure can be performed promptly and
thoroughly , allowing you to get back to the task at hand
: RACING.
Additional Info
|
 |
• Regular brake fluid flushing is important
on all vehicles , but on ABS equipped braking systems ,
this procedure is even more critical.
• European car manufacturers generally
have a more “black and white” attitude regarding brake
fluid service , and can have a very simple policy on new vehicle
warranties , namely ; yearly brake fluid flushing is required to
maintain the vehicle warranty on most hydraulic brake parts.
• SpeediBleed™
is also the ideal clutch hydraulic
tool. If we do not have the appropriate adapter for your clutch
master cylinder , we can provide a male coupler for you to build
your own , or if you prefer , we can adapt your old resevoir cap
for you.
 |
“We take
our SpeediBleed™
Race Kit to the track all the time.
We have loaned it out several times , people can't believe
how fast and easy it is to use and what a great job it does.
“
“Our lead mechanic took
our SpeediBleed™
to the Daytona 24 hour and used
it to bleed the clutch on a GT-3 Porsche when nothing else
seemed to work , it saved the day and the car finished in
the top 15 overall! “
“Track side
or in the shop , our SpeediBleed™
Race Kit allows one person to do
a better and faster brake flush or bleed than our current
air pressure bleeding system.”
Joe Marko,
President, HMS Motorsport |
Contact
us for your clutch bleeding needs or any other requirements : speedibleed@shaw.ca
|
|
